How To Choose A Reverse Osmosis System
How To Choose A Reverse Osmosis System
Choosing a Reverse Osmosis system for your home (or office) depends on so many factors. You can make your best decisions if you have a general understanding of the basics of the process. The technical terms will fall into places as we walk you through some of the most frequently-asked-questions both from customers.
In a nutshell, reverse osmosis is the process where contaminated water is forced through a semi-permeable membrane via pressure to harvest pure clean water at the other end. The membrane strained out TDS (total dissolved solids) composed mostly of salts, metals, microorganisms, minerals, chemicals, etc.)
Water quality
Is the water supply potable?
An R/O system should be installed only if the water supply is deemed bacteriologically safe for human consumption, is disinfected or sterilized on a regular basis.
What is the daily quantity of pure water required?
It should produce at least ½ gallon of drinking water per person/per day.
Is the water supply adequately pre-treated?
The presence of contaminants such as iron, manganese, or hydrogen sulfide should be removed by pretreatment.
What is the level of TDS?
Drinking water should have a TDS of below 500. Water from wells have a TDS of 1000 to 5000, seawater has a TDS of 40,000.
Is the feed water supply chlorinated or unchlorinated?
If unchlorinated, chose a TFC membrane to withstand bacteria attack. If chlorinated, chose a CTA membrane that is not chlorine-sensitive. The membranes have to be replaced around every 2 years, depending on the quantity and quality of water.
What about water acidity?
The average pH is 6.9 to 7.5. Low pH is very corrosive to metals. A pH of 6.9 is ten times more acidic than at a Ph OF 7.0.
Booster pumps
Is a booster pump required?
A booster pump is needed if the water pressure is less than 50 psi, if the TDS in your water supply is over 1000, or if the water is very cold.
Performance factors
In the end, there are four factors that ultimately affect the performance of an R/O unit – 1) incoming water pressure, 2) temperature, 3) the TDS number and, 4) the quality of the filters and membranes used.
How much water is produced is governed by the pressure on the net membrane. If the pressure is increased, production goes up. It is also dependent on the temperature. The cooler the feed water, the lower the rate of production.
The force that binds the water molecules to dissolved ions or solids is called osmotic pressure. Now, the higher the number of the total dissolved solids (TDS) in the water, the higher is the molecular force that binds them.
These water molecules that are bound to the molecules of the dissolved solids need to be separated to pass through the pores of the membrane. To break the bond, there must be pressure applied on the water.
In the R/O process, more than one filter and membrane may be used. The pre-filters are for the sediments (sand silt, dirt and others). Then there are the carbon filters which pick up the chlorine which destroys the osmosis membrane.
Finally, the heart of the reverse osmosis system: the reverse osmosis membrane. The most common is the spiral wound. There are two choices, too – the CTA (cellulose tri-acetate) which is chlorine tolerant and the TFC/TFM (thin film composite /thin film material) which is not chlorine tolerant.
If the feed water is not chlorinated, a TFC membrane is used because of its greater resistance to bacterial attack. CTA membranes not sensitive to chlorine may be used. Most systems, however, use TFC membranes, with a carbon filter support.
These are the details to consider in the choice of R/O system for your home or office. Don’t forget to also discuss them with your supplier for more inside information on how to choose a reverse osmosis system.
More Articles
The Many Applications Of Reverse Osmosis
Singapore Leads Efforts To Improve Reverse Osmosis Technology
Comparing Filtration With Reverse Osmosis
Frequently Asked Questions On Reverse Osmosis
Reverse Osmosis Could Filter Out Unlikely Chemicals
Reverse Osmosis As A Water Treatment Process
Related Products And FREE Videos
More Articles
Pros And Cons Of Reverse Osmosis
... the same for important trace minerals found in water. This is because the semi-permeable membranes used are almost always impermeable to naturally occurring trace minerals in water. Such minerals are identified as responsible for providing water better taste. They also facilitate a good function to the human system. Needless to say, if drinking water is deprived of such minerals, it could be totally unhealthy and less likely for drinking. It is also a widely known fact that reverse osmosis puts more water to waste. In general, it would take about three gallons of water to be wasted for producing ...
Reverse Osmosis Some User Tips
... produce around a gallon of water every two to four hours. It is not advisable for activities like washing or showering. R/O systems for the entire household would be extremely expensive. Foul-smelling hot water The chemical that causes it is in the incoming water, most noticeable in hot water because the chemical becomes gas at higher temperatures. The rotten egg smell is caused by hydrogen sulfide present in the feed water (source) and carried to your house. Odors like petroleum or rotten eggs can be removed by using activated carbon filters, available in cartridge filtration systems or stand-alone ...
Industrial Sector Increases Use Of Reverse Osmosis
... pharmaceutical applications. Food and beverage industry uses it to process beverages and food products for quality and safety purposes. Even the semiconductor and metal finishing sectors are widely using reverse osmosis. In the semiconductor industry, the process is included as a standard component of treatment for the production of ultrapure water for different uses. In metal finishing, reverse osmosis systems are applied to metal finishing operations, which include production of several types of zinc, copper, and nickel. The power generation industry is currently one of the heaviest users of reverse ...
Is Reverse Osmosis Bad For Our Health
... filter usually uses a sediment type which prevents rust and calcium carbonate to pass through. An activated carbon filter is then next. With this one organic chemicals and chlorine are trapped. The water then passes through a reverse osmosis filter made up of thin composite membrane. Then after that one would find another layer carbon filter which is there to ensure that any particles that was able to push their way through is prevented from going further. You can now see clearly where the reverse osmosis process has overdone the filtering. Unlike carbon filters, reverse osmosis removes any molecules ...
New Method Developed To Make Reverse Osmosis Cheaper
... cheaper especially within developing nations. Desalination is a widely used process of purifying seawater or even brackish water to produce potable water that is safer for drinking and consumption of people. The process is massively used in about a hundred countries globally, with nations in the Middle East and other desert areas as the heaviest users. It is also becoming popular in other nations where growing population has depleted available potable water sources, like in Australia, China, Spain, and several states in the US. Desalination is effective, but it is at the same time very costly. Reverse ...